Mechanical Systems and Signal Processing

Research outputs

  1. 2018
  2. Published
  3. Published

    Vibration analysis of paper machine’s asymmetric tube roll supported by spherical roller bearings

    Heikkinen, J. E., Ghalamchi, B., Viitala, R., Sopanen, J., Juhanko, J., Mikkola, A. & Kuosmanen, P., 1 May 2018, In : Mechanical Systems and Signal Processing. 104, p. 688-704 17 p.

    Research output: Contribution to journalArticleScientificpeer-review

  4. 2017
  5. Published

    Time-frequency vibration analysis for the detection of motor damages caused by bearing currents

    Prudhom, A., Antonino-Daviu, J., Razik, H. & Climente-Alarcon, V., 1 Feb 2017, In : Mechanical Systems and Signal Processing. 84, p. 747-762 16 p.

    Research output: Contribution to journalArticleScientificpeer-review

  6. 2016
  7. Published

    A 2D magnetic and 3D mechanical coupled finite element model for the study of the dynamic vibrations in the stator of induction motors

    Martinez, J., Belahcen, A. & Detoni, J. G., Jan 2016, In : Mechanical Systems and Signal Processing. 66-67, 1, p. 640-656 17 p.

    Research output: Contribution to journalArticleScientificpeer-review

  8. 2015
  9. Published

    Tyre contact length on dry and wet road surfaces measured by three-axial accelerometer

    Matilainen, M. & Tuononen, A. J., 2015, In : Mechanical Systems and Signal Processing. 52, p. 548558

    Research output: Contribution to journalArticleScientificpeer-review

  10. 2013
  11. Published

    Detection, identification, and quantification of sensor fault in a sensor network

    Kullaa, J., Oct 2013, In : Mechanical Systems and Signal Processing. 40, 1, p. 208-221 14 p.

    Research output: Contribution to journalArticleScientificpeer-review

  12. 2012
  13. Published

    Including slot harmonics to mechanical model of two-pole induction machine with a force actuator

    Sinervo, A. & Arkkio, A., 2012, In : Mechanical Systems and Signal Processing. 32, October, p. 282291

    Research output: Contribution to journalArticleScientificpeer-review

  14. 2011
  15. Published

    Distinguishing between sensor fault,structural damage, and environmental or operational effects in structural health monitoring

    Kullaa, J., 2011, In : Mechanical Systems and Signal Processing. 25, 8, p. 2976-2989

    Research output: Contribution to journalArticleScientificpeer-review

  16. Published

    Transient tracking of low and high-order eccentricity-related components in induction motors via TFD tools

    Climente-Alarcon, V., Antonino-Daviu, J., Riera-Guasp, M., Pons-Llinares, J., Roger-Folch, J., Jover-Rodriguez, P. & Arkkio, A., 2011, In : Mechanical Systems and Signal Processing. 25, 2, p. 667-679

    Research output: Contribution to journalArticleScientificpeer-review

  17. 2010
  18. Published

    Sensor validation using minimum mean square error estimation

    Kullaa, J., 2010, In : Mechanical Systems and Signal Processing. 24, 5, p. 1444-1457

    Research output: Contribution to journalArticleScientificpeer-review

  19. 2009
  20. Published

    Detection of combined faults in induction machines with stator parallel branches through the DWT of the start-up current

    Antonino-Daviu, J., Jover Rodriguez, P., Riera-Guasp, M., Pineda-Sánchez, M. & Arkkio, A., 2009, In : Mechanical Systems and Signal Processing. 23, 7, p. 2336-2351

    Research output: Contribution to journalArticleScientificpeer-review

  21. 2008
  22. Published

    A simplified scheme for induction motor condition monitoring

    Jover Rodriguez, P., Negrea, M. & Arkkio, A., 2008, In : Mechanical Systems and Signal Processing. 22, 2, p. 1216-1236

    Research output: Contribution to journalArticleScientificpeer-review

  23. 2007
  24. Published

    DWT analysis of numerical and experimental data for the diagnoses of dynamic eccentricity in induction motors

    Jover, P., Jose, A-D., Riera, M., Arkkio, A. & Roger-Folch, J., 2007, In : Mechanical Systems and Signal Processing. 21, 6, p. 2575-2589

    Research output: Contribution to journalArticleScientificpeer-review

  25. Published

    Vibration-based structural health monitoring using output-only measurements under cahnging environment.

    Deraemaeker, A., Reynders, E., De Roeck, G. & Kullaa, J., 2007, In : Mechanical Systems and Signal Processing. 22, p. 34-56

    Research output: Contribution to journalArticleScientificpeer-review

  26. 2003
  27. Published

    Damage detection of the Z24 Bridge using control charts

    Kullaa, J., 2003, In : Mechanical Systems and Signal Processing. 17, 1, p. 163-170

    Research output: Contribution to journalArticleScientificpeer-review

ID: 336165